乙醇汽油与普通汽油非常规污染物排放特性对比研究

在一台满足国Ⅴ排放标准的双喷射(气口喷射+缸内直喷)汽油机上开展了燃用E10乙醇汽油(乙醇体积比为10%)对发动机非常规排放特性影响的试验研究.使用傅里叶变换红外分析仪(FTIR)测量了饱和烃、不饱和烃、芳香烃及醇、醛等非常规污染物排放量,对比分析了双喷射模式时各工况下E0和E10两种燃料的非常规排放水平.结果表明,双喷射模式下,加入乙醇有效降低了乙烯、1,3-丁二烯、苯和甲苯的排放量,但会导致乙醛排放升高.双喷射模式下,随着负荷增加,两种燃料下的1,3-丁二烯和甲苯排放呈现先升高后降低的趋势,乙烯、甲醛和苯排放则先降低后升高.乙醇能抑制1,3-丁二烯、乙烯生成,抑制效果为PFI模式优于双喷射模式,GDI模式抑制量最低.PFI和GDI模式下E10的甲醛排放均显著升高,但双喷射模式有效抑制了甲醛排放的增加.     

农闲期城郊农田灌溉水中典型污染物含量与评价——以西北江三角洲为例

摸查了农田灌溉系统水环境经农（夏）闲期降水等外部强干预调理后的环境污染物含量——该值理论上是环境自净作用之后的最不利值,对农田灌溉系统水环境进行水质评价,探究其对农田土壤质量的潜在污染风险.于2019年6月中旬—7月下旬（降雨集中期）,分别在西北江三角洲城市（清远市、佛山市和江门市）实验基地周边筛选研究区,并在雨后对有覆水的水源区域、灌渠、蓄水池和田间水等采集上覆水,共采得水样27×2份,对其pH值、悬浮物（SS）、矿化度、总磷（TP）、氨氮（NH₄⁺-N）、Cd、As、Pb、Cu和Zn的含量进行检测;对各研究区pH值、SS的成因和影响,矿化度的等级,重金属均值分布等进行分析;对全样品TP、NH₄⁺-N、重金属含量进行Pearson相关性分析和描述性特征分析;通过单因子水质标识指数P_i和综合水质标识指数P分别对各采样点、各构成项目和各研究区进行水质评价.研究发现雨后农田灌溉系统水环境构成复杂,物质呈无显著性差异的迁移,灌溉沿程上覆水中大部分物质可能处于动态平衡,受局部环境影响变小,TP、NH₄⁺-N和重金属等迁移物质主要还是灌溉水体中原有的,受外力驱动扰动后在水动力作用下可能以氮磷结合形态沿灌溉系统发生远距离迁移;使用河流水质标识指数法评价农田灌溉系统水环境,发现该法可以刻画局部灌溉的水质态势,对农田灌溉系统水环境的含量特征评价做出科学、合理的解释,也可以做出综合性定量评价.虽然灌溉水系统结构差异较大,但是从整体上可以初步得出农闲期西北江三角洲农田灌溉水的灌溉风险不高的结论,总体综合水质评价级别为Ⅰ类~Ⅱ类,达到水环境功能区的使用要求.     

生态文明视角下的国土空间底线管控：“双评价”与国土空间规划监测评估预警

生态文明新时代下的空间规划体系对国土空间底线管控提出了明确要求,“双评价”与国土空间规划监测评估预警是底线思维的体现。研究“双评价”与国土空间规划监测评估预警在国土空间底线管控中的作用和地位,通过国土空间规划“一张图”实施监督信息系统的建设,对二者的联系及其相互作用进行体现,构建二者的联动方式,服务于国土空间底线管控及治理的全过程。“双评价”与国土空间规划监测评估预警共同组成底线管控的两个阶段,前者是开展底线管控的基础,后者是底线管控的路径和手段,两者皆是生态文明新时代下国土空间规划底线管控的重要工具,需以国土空间规划“一张图”实施监督信息系统为基础加强两者的有机结合。     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

苯醌对聚合硅酸铁多相UV-Fenton体系的增效机制

通过构建苯醌增效聚合硅酸铁多相UV-Fenton体系,讨论了体系中橙Ⅱ的脱色和降解途径.在研究苯醌浓度对聚合硅酸铁铁离子的释放、Fe²⁺与Fe³⁺之间的转化、H₂O₂分解和·OH生成影响的基础上,提出了苯醌对聚合硅酸铁多相UV-Fenton体系的增效机制.结果表明,随苯醌浓度的增加,其紫外光下光解还原聚合硅酸铁并释放Fe²⁺的程度增大、H₂O₂分解速度加快、产生·OH浓度峰值增高且出现的时间提前;苯醌增效体系释放于溶液中的Fe²⁺可以通过Fenton反应转化成Fe³⁺,反应结束后聚合硅酸铁能重新吸附Fe³⁺并使其浓度降低,避免了增效体系铁离子的二次污染.本研究将为多相催化剂催化过程的调控提供新的视角,为多相光助-芬顿反应在有机废水资源化中的应用提供理论依据和技术支持.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

On-going nitrification in chloraminated drinking water distribution system (DWDS) is conditioned by hydraulics and disinfection strategies

Within the drinking water distribution system (DWDS) using chloramine as disinfectant, nitrification caused by nitrifying bacteria is increasingly becoming a concern as it poses a great challenge for maintaining water quality. To investigate efficient control strategies, operational conditions including hydraulic regimes and disinfectant scenarios were controlled within a flow cell experimental facility. Two test phases were conducted to investigate the effects on the extent of nitrification of three flow rates (Q = 2, 6, and 10 L/min) and four disinfection scenarios (total Cl₂=1 mg/L, Cl₂/NH₃-N=3:1; total Cl₂=1 mg/L, Cl₂/NH₃-N=5:1; total Cl₂=5 mg/L, Cl₂/NH₃-N=3:1; and total Cl₂=5 mg/L, Cl₂/NH₃-N=5:1). Physico-chemical parameters and nitrification indicators were monitored during the tests. The characteristics of biofilm extracellular polymetric substance (EPS) were evaluated after the experiment. The main results from the study indicate that nitrification is affected by hydraulic conditions and the process tends to be severe when the fluid flow transforms from laminar to turbulent (2300<Re<4000). Increasing disinfectant concentration and optimizing Cl₂/NH₃-N mass ratio were found to inhibit nitrification to some extend when the system was running at turbulent condition (Q = 10 L/min, Re = 5535). EPS extracted from biofilm that was established at the flow rate of 6 L/min had greater carbohydrate/protein ratio. Furthermore, several nitrification indicators were evaluated for their prediction efficiency and the results suggest that the change of nitrite, together with total organic carbon (TOC) and turbidity can indicate nitrification potential efficiently.     

关于在长江经济带布局以水质改善为目标的流域生态缓冲体系的思考

生态缓冲带能够有效减缓流域内的人类活动或自然过程对水环境和水生态系统的影响.在长江经济带构建流域生态缓冲体系,对长江生态保护修复具有十分重要的意义.讨论了构建流域生态缓冲体系涉及的生态缓冲带位置选择、缓冲体系所占最低面积比率、宽度划定等一些基本的原则要求;利用卫星遥感影像数据,提取各汇水单元的地形特征、土地利用类型特征、土壤类型、土壤侵蚀强度、水文水系等数据,对长江经济带流域生态缓冲体系进行布局.结果表明:①长江经济带内林草地是主要土地利用类型,占区域总面积的62.46%,但是分布很不均匀,主要集中在西部高地和中下游的丘陵地带,在人口密集、农田密集的区域分布偏少;城镇用地主要集中在长江中下游地区.②土壤类型空间差异显著,浙江省、江苏省、湖南省、江西省及安徽省大部分区域的土壤多是黏性比较大,污染物迁移能力较低;而污染物迁移能力较强的砂质土或者土层较薄的山地草甸土主要分布在四川省北部、西北部.水力侵蚀、风力侵蚀和冻融侵蚀均有分布,且以水力侵蚀为主,建议在中度及以上侵蚀强度区域尽量减少污染源,重点布置缓冲带,增加该区域的缓冲力度.③长江经济带范围内可以利用的中小型湿地、小型河流支浜的面积至少有1.4×104 km2,再结合林草缓冲带,就可以形成一个生态缓冲体系.④在土地利用类型分布结果基础上,叠加土壤侵蚀强度和水系分布,将污染源区、中度及以上侵蚀强度区、水体区作为缓冲对象,建立缓冲体系的重点区域,总面积约14.26×104 km2,占长江经济带总面积的6.95%.对照欧美地区的研究,6.95%的缓冲体系面积占比是偏低的,需要在长江经济带开展深入研究来确定适宜的缓冲体系面积比,推进长江经济带流域生态缓冲体系的构建.